Transformer OLTC diagnostic system PKR-2M

有载分接开关维护检查

更多

电阻型OLTC不可拆卸诊断(DRM方法)

更多

电阻式OLTC接触器切换振荡器

更多

电阻器和电抗器型OLTC的循环图记录

更多

自动自调节至有载分接开关OLTC

更多

反应器型有源分接开关OLTC在“静态”模式下检查

更多

符合人体工程学的探头或鳄鱼夹电缆

更多

独立自给的电源,在仪器和PC中存储,传输和分析测量结果

更多

该系列仪器以两种型号供应

更多

PKR-2M旨在用于所有类型的OLTC设备(电阻器和电抗器)的可拆卸诊断,以及不可拆卸的诊断,这使得能够在不拆除接触器油箱盖的情况下使用限流电阻器诊断OLTC。

PKR-2M能够诊断由华明,MR,ABB,现代重工保加利亚制造的OLTC设备。观看有关PKR-2M

OLTC分析仪的详细视频评论,请访问上方或我们的YouTube。 观看视频subscribe

OLTC不可拆卸检查(DRM方法)能够在不打开油箱的情况下使用限流电阻对OLTC进行快速诊断。根据在DRM模式下获得的结果,构建了两个图表:电阻与时间和电导率与时间的关系。

例如,对于RS、RNOA等型OLTC而言,可以确定主接触器和电弧接触器触点的操作正确性、其状况(烧毁或未烧毁触点)、限流电阻器完整性。对于RNTA – 35/320型OLTC,其接触器和选择器被更改为精细控制开关装置,可以检查主触点和电弧触点,限流电阻条件以及断路器所有固定触点的表面状况,移动触点通过该触点移动。

基于 DRM 方法的不可拆卸检查模式的应用不需要拆卸:

  • 打开无故障/故障有载分接开关的油箱或舱口和排油口;
  • OLTC诊断的额外资金和人工成本;
  • 连接附加元件或了解已检查的OLTC器件的限流电阻器的电阻,因为对某个OLTC的所有微调都是在仪器中自动进行的。

切换振荡器能够检测驱动延迟、同相致动的非同时性和切换期间的弹跳。

所有特征均采用:

PKR-2M配有用于周期图记录的特殊换能器。它与不同驱动器的轴的接口配有一组轴和衬套,只需戴上轴突起即可安装,无需任何工具即可安装。

所有特征都被取缔:

无需额外的元件(例如电阻器)或了解已检查的OLTC器件的限流电阻器的电阻即可测量参数。对特定OLTC的所有调节都在仪器中自动执行。

反应器OLTCS可以在PKR-2设备的帮助下以静态模式进行检查。用户用标准成套的手柄以慢动作旋转驱动轴。此时,触点关闭/打开的时刻以度数以及电压和电流值显示在设备的显示屏上。

为了方便直接连接到OLTC的触点,当部分或全部排油打开油箱时,PKR-2M配备了特殊的长探头。

无需接触式探头,即可使用带有鳄鱼夹的电缆连接到 OLTC。在这种情况下,应从接触器油箱进行部分或全部排油,或者应从变压器油箱中完全移除OLTC。

PKR-2M配备了内置电池,可提高其移动性和易用性。自主电源允许您在整个工作日内在变电站或车间的大范围内操作设备,而无需充电。内置电池使您免于电源线、电源网络扩展和接地的麻烦。

该仪器配备了大型传感器彩色图形显示屏,能够以图形或表格形式表示信息。高亮度和对比度使处理图形变得更加容易。

测量结果可以通过以下方式之一存储:在仪器的非易失性存储器中,在外部闪存中,或者可以传输到PC。

此外,仪器可以通过仪器键盘、传感器显示器或 PC 进行控制。最后提到的功能允许您坐在车内使用PC记录图表,这在寒冷季节很重要且舒适。

  PKR-2 PKR-2M
有载分接开关OLTC检查模式
可拆卸
可拆卸和不可拆卸(DRM 方法)*
内置电池电源
没有
可用
(操作时间从2到16小时)

*不可拆卸的检查模式可以在不打开接触器油箱盖的情况下,使用限流电阻对OLTC进行原位诊断。该模式基于 DRM 方法(动态电阻测量),包括通过绕组测量电流强度,其中 OLTC 接通。

规格
时间间隔测量范围 0.01 - 1200 s
精度 ±(3 + tx) × 10-4, where tx - measured time interval, sec
分辨率 ±0.1 ms
角运动测量范围 2 - 360 º
精度 ±0.56 º
DC直流电流测量范围 1 - 4 А
DC直流电阻测量范围 1 - 20 V
直流电阻测量范围 1 - 20 Ω
精度 ±5 %
每个通道电阻测量的采样频率 10 ±0.1 kHz
最长圆形图注册时间 20 min
最长 DRM 示波图注册时间 20 min
PC 连接 USB and USB host
显示器 彩色图形显示屏,触摸屏, 640 x 480 pixels
电源内置电池 锂离子电池
PKR-2M 的电池运行时间(连续运行中) 2-8 h
电池充电时间 2,5 h
待机模式下的最大功耗 15 W
测量模式下的最大功耗 210 W
电源(电源电压) 150-242 V AC, 47-63 Hz 150-300 V DC
操作温度范围, ºС -20ºС - +40ºС
环境防护 IP 64(设备盖关闭) IP 20(设备盖打开)
测量单元最大重量 6.1 kg
尺寸 360 x 290 x 165 mm
用户界面和用户手册语言 English
质保期 3 years
计量周期 3 years

Additional complete set (on order)

照片 项目,索引 应用
DRM test cable
  • DRM test cable
  • 035.38.00.000
  • DRM test cable
  • 035.38.00.000

To be used together with the standard 035.39.00.000 test cable during non-demountable diagnostic (DRM-method) for connection to transformers above 200 kV and to autotransformers. Length - 6 m.

Additional resistor
  • Additional resistor
  • 035.40.00.000
  • Additional resistor
  • 035.40.00.000

It is used for non-demountable diagnostic of OLTCs to filter out interference generated during the measurements due to self-excitation of the transformer.

Complete set of contact probes and special tool bag
  • Complete set of contact probes and special tool bag
  • 035.41.00.000
  • Complete set of contact probes and special tool bag
  • 035.41.00.000

Modular probes 7 x 1.7 m (diameter of each: 9 mm) for connection to the contacts of OLTC during the demountable diagnostics. Removable contact tips are in two versions: sharp cone-shaped and in a form of spring-loaded gripper.

To the probes additionally can be ordered a special tool bag for convenient storage and carrying.

Axes for DP22 transducer fixation to the output shaft
  • Axes for DP22 transducer fixation to the output shaft
  • Axes for DP22 transducer fixation to the output shaft

Select the axis for DP22 transducer fixation to the output shaft:

  • Axis No. 1 - for OLTC drives of BUL type (035.25.01.000);
  • Axis No. 2 - for OLTC drives of PDP, МА-1, МAK-1 types (035.25.02.000);
  • Axis No. 3 - for OLTC drives of PDP, МА-1, MAK-1 types (035.25.03.000);
  • Axis No. 4 - for OLTC drives of PDP, МА-1, MAK-1 types (035.25.04.000);
  • Axis No. 6 - for OLTC drives of PDP-4U type (when a manual drive is used) (035.25.06.000);
  • Axis No. 9 - for OLTC drives of PDP-4U type (when an electric drive is used) (035.25.09.000);
  • Axis No. 7 - for OLTC drives of MZ-4.1, MZ-4.4 types (when the electric drive is used) (035.25.07.000);
  • Axis No. 8 - for OLTC drives of MZ-4.1, MZ-4.4 types (when the manual drive is used) (035.25.08.000);
  • Axis No. 11 - for OLTC drives of SMA-7 (SMS-China), ED 100/200 S, ED 100/200 S types (MR-Germany) (when the manual drive is used) (035.25.11.000);
  • Axis No. 12 - for OLTC drives of SMA-7 (SMS-China), ED 100/200 S, ED 100/200 S types (MR-Germany) (when the electric drive is used) (035.25.12.000);
  • Axis No. 13 - for OLTC drives of VAKUTAP type manufactured by MR (035.25.13.000).

USB 2.0 A-B cable
  • USB 2.0 A-B cable
  • USB 2.0 A-B cable

For the instrument connection to PC (length – 1.8 m).

Manipulating rod
  • Manipulating rod
  • 010.41.00.000
    010.41.00.000-01
    010.41.00.000-02
  • Manipulating rod
  • 010.41.00.000
    010.41.00.000-01
    010.41.00.000-02

Manipulating rod is designed for test cables connection from the ground or from the tank cover to the bushings of high-voltage circuit breakers, and to the structural elements of high-voltage disconnecting switches and earthing devices, without the use of ladders or elevated platforms.

The manipulating rod is completed with special extension cables. There is a Kelvin clamp with current and potential contacts to connect to the object on one side, and a contact pad on the other side. The device test cable is connected to the contact pad from the ground or a tank cover.

Manipulating rod extension cable is made according to a four-wire (Kelvin) scheme with the test current capacity of 100 A in the presence of a good contact.

Standard complete set

照片 项目,索引 应用
Main instrument PKR-2М
  • Main instrument PKR-2М
  • 035.00.00.000-1
  • Main instrument PKR-2М
  • 035.00.00.000-1

Instrument and accompanying documents: Calibration Certificate, User Manual, Log Book, PC software.

Test cable with a connector<br>and A, B, C pole cables
  • Test cable with a connector
    and A, B, C pole cables
  • 035.34.00.000
    035.34.00.000-01
    035.34.00.000-02
    035.39.00.000
  • Test cable with a connector
    and A, B, C pole cables
  • 035.34.00.000
    035.34.00.000-01
    035.34.00.000-02
    035.39.00.000

带连接器的测试电缆 1 x 8 m。A、B、C 相电缆 3 x 1.5 m,钳口最大可达 25 mm。

该电缆可用于可拆卸诊断模式,以连接到油箱内变压器有载分接开关的触点,并可以用在不可拆卸诊断模式(DRM测试)中用于连接到高达220 kV的变压器输入端。

要连接到220 kV以上的变压器和自耦变压器的输入端,请选择带夹具的035.38.00.000测试电缆,该电缆与035.39.00.000连接器一起使用。

Short-circuit cable
  • Short-circuit cable
  • 035.31.00.000
  • Short-circuit cable
  • 035.31.00.000

Short-circuit cable 3 x 12 m for non-demountable diagnostic of OLTC devices of power transformers and autotransformers.
At the end of each short-circuit cable there are two crocodile clips with jaw up to 50 mm.

Angular movement transducer DP22
  • Angular movement transducer DP22
  • 035.26.00.000
  • Angular movement transducer DP22
  • 035.26.00.000

The transducer enables to measure the angle and speed of the OLTC shaft rotation. Angle measuring range – 2 - 360º (it is necessary to select an appropriate axis from the additional complete set).

C-clamp
  • C-clamp
  • 035.30.00.000
  • C-clamp
  • 035.30.00.000

To fix the DP22 transducer on the OLTC drive.

Handle
  • Handle
  • 028.25.02.000
  • Handle
  • 028.25.02.000

To fix the magnetic clamp.
Handle for the OLTC shaft rotation. It is used together with axis from the additional complete set.

Axis No.10 together with a bushing
  • Axis No.10 together with a bushing
  • 035.25.00.000
    028.25.01.008
  • Axis No.10 together with a bushing
  • 035.25.00.000
    028.25.01.008

Axis No. 10 for the OLTC drives of the MZ-4.1; M3.2; M3-4 type. For the drive of PDP-4U type this axis is used together with the bushing.

Axises for other drives are represented in the additional complete set.

Mains cable
  • Mains cable
  • 018.09.00.0000
  • Mains cable
  • 018.09.00.0000

For connecting the instrument to the power supply. Temperature range -15ºС - +45ºС (length – 2 m).

Ground cable
  • Ground cable
  • 010.01.00.000
  • Ground cable
  • 010.01.00.000

For instrument case grounding. Equipped with a ground clamp and screw end cap. Nominal current – 50 А (length – 2 m).

Fuses
  • Fuses
  • Fuses

Type VP2B-1V-2A (ВП2Б-1В-2А) (2 pcs) to protect the power source.

Tool bag
  • Tool bag
  • 126.06.00.000
  • Tool bag
  • 126.06.00.000

Robust, convenient, wear proof bag for transportation of cables, documentation, and other accessories to PKR-2M. The bag is especially useful when the set is carried to an object, so that all the needed accessories are kept together.
Weight 0.6 kg.

我们使用加载项. 通过继续浏览网站,您同意我们处理您的个人数据和隐私政策。隐私政策.